Synthesis of Ti3C2Fx MXene with controllable fluorination by electrochemical etching for lithium-ion batteries applications

Ti₃C₂T_x MXene has attracted remarkable attention due to its promising applications in energy storage and sensors. However, traditional MXene preparation methods used HF as etchant, which was highly toxic and harmful to human and environment. Moreover, the aqueous etchants will also result in the combination of OH, O and F groups on the surfaces, making it difficult to control the varieties and contents of the surface terminations. In this paper, a green and mild electrochemical exfoliation method was proposed to synthesize Ti₃C₂F_x and synchronously control its fluorination degree on the surface. A non-aqueous ionic liquid, [BMIM][PF₆]-based solution was used as electrolyte. The as-prepared Ti₃C₂F_x was fluorinated with the CF and TiF₃ groups, which were electrochemically active and contributed to the excellent cycling stability of the MXene anode-based Li-ion batteries. These findings provided a facile strategy to prepare MXene materials and dope MXene with tailored property for MXene-based energy devices applications.     

Microstructural and mechanical properties assessment of transient liquid phase bonding of CoCuFeMnNi high entropy alloy

The transient liquid phase (TLP) bonding of CoCuFeMnNi high entropy alloy (HEA) was studied. The TLP bonding was performed using AWS BNi-2 interlayer at 1050 °C with the TLP bonding time of 20, 60, 180 and 240 min. The effect of bonding time on the joint microstructure was characterized by SEM and EDS. Microstructural results confirmed that complete isothermal solidification occurred approximately at 240 min of bonding time. For samples bonded at 20, 60 and 180 min, athermal solidification zone was formed in the bonding area which included Cr-rich boride and Mn₃Si intermetallic compound. For all samples, the γ solid solution was formed in the isothermal solidification zone of the bonding zone. To evaluate the effect of TLP bonding time on mechanical properties of joints, the shear strength and micro-hardness of joints were measured. The results indicated a decrement of micro-hardness in the bonding zone and an increment of micro-hardness in the adjacent zone of joints. The minimum and maximum values of shear strength were 100 and 180 MPa for joints with the bonding time of 20 and 240 min, respectively.     

镍基高温合金GH202高温氧化后的微观组织演变

研究了镍基高温合金GH202在800~1100 ℃高温氧化后晶粒、碳化物和强化相的演变过程。采用透射电子显微镜、扫描电子显微镜和电子背散射衍射对其微观结构进行了表征。结果表明：镍基高温合金的硬度随氧化温度的升高而降低，1100 ℃氧化100 h后，硬度降低了43.5%。800和900 ℃氧化后晶粒生长速度较慢，而经900 ℃氧化后晶界碳化物析出显著增加。在1000和1100 ℃氧化后，晶粒尺寸明显增大。氧化过程中晶界迁移是由晶界两侧自由能差决定，温度越高，晶界向曲率中心迁移越快，大量细小晶粒被吞并形成了大晶粒。大块状碳化物（MC）分解成大量的碳原子，与Cr原子结合形成少量的富Cr颗粒状M₂₃C₆。在900 ℃氧化150 h后，M₂₃C₆演化为富Ti的M₆C。随着氧化温度的升高，碳化物在γ相中回熔。在800、900和1000 ℃氧化后，γ′相逐渐长大，在1100 ℃氧化100 h后，完全溶解于γ相。     

High-Throughput Screening for Phase-Change Memory Materials

Phase change memory (PCM) is an emerging non-volatile data storage technology concerned by the semiconductor industry. To improve the performances, previous efforts have mainly focused on partially replacing or doping elements in the flagship Ge-Sb-Te (GST) alloy based on experimental “trial-and-error” methods. Here, the current largest scale PCM materials searching is reported, starting with 124 515 candidate materials, using a rational high-throughput screening strategy consisting of criteria related to PCM characteristics. In the results, there are 158 candidates screened for PCM materials, of which ≈68% are not employed. By further analyses, including cohesive energy, bond angle analyses, and Born effective charge, there are 52 materials with properties similar to the GST system, including Ge₂Bi₂Te₅, GeAs₄Te₇, GeAs₂Te₄, so on and other candidates that have not been reported, such as TlBiTe₂, TlSbTe₂, CdPb₃Se₄, etc. Compared with GST, materials with close cohesive energy include AgBiTe₂, TlSbTe₂, As₂Te₃, TlBiTe₂, etc., indicating possible low power consumption. Through further melt-quenching molecular dynamic calculation and structural/electronic analyses, Ge₂Bi₂Te₅, CdPb₃Se₄, MnBi₂Te₄, and TlBiTe₂ are found suitable for optical/electrical PCM applications, which further verifies the effectiveness of this strategy. The present study will accelerate the exploration and development of advanced PCM materials for current and future big-data applications.     

一种植物油中苯并（a）芘含量测定的固相萃取前处理方法

为了建立一种准确性高、成本低的植物油中苯并(a)芘测定的样品前处理方法，基于GB 5009.7—2016以自制氧化铝柱为固相萃取柱，采用单因素试验对称样量、洗脱剂量、洗脱流速、吸附剂存放时间、吸附剂量这5个影响植物油中苯并（a）芘洗脱的因素进行研究，优化前处理条件，并对测定方法进行考察。结果表明：优化的前处理条件为称样量0.100 0 g、洗脱剂量120 mL、吸附剂（氧化铝）量22 g、洗脱流速1滴/2 s、吸附剂存放时间少于12周；方法检出限为0.2 μg/L，样品加标回收率为94.23%～100.00%，RSD为1.20%～7.36%；同一样品测定结果与SGS测定值接近，相对平均偏差为2.36%～3.50%。说明本试验方法测定结果准确，可应用于油脂企业植物油中痕量苯并（a）芘的测定。     

冷低压分离器油相系统铵盐垢下腐蚀风险的模拟预测

为探究某加氢装置高压换热器管束腐蚀泄漏原因，利用Aspen Plus工艺模拟软件计算了冷低压分离器油相（简称冷低分油）中水质量分数分别为1%,2%,3%时，冷低分油系统的露点温度、氯化铵结晶温度、氯化铵潮解点温度和相对湿度。结果表明：相较于经验的露点温度预测方法，通过引入潮解点、划分系统“湿环境”温度范围判断氯化铵垢下腐蚀风险区域的方法与实际腐蚀案例更为切合；在3种油相含水条件下，换热器管束存在氯化铵垢下腐蚀的“湿环境”温度范围分别为：50~103 ℃,50~161 ℃,50~176 ℃；随着油相中含水量的提高，“湿环境”腐蚀区域逐渐向高温部位迁移，预计铵盐导致的垢下腐蚀将会愈加严重。     

基于Matlab的量子激光雷达稳频通信模拟系统设计

传统通信模拟系统设计较为复杂,导致模拟过程消耗能量较大,不能准确模拟稳频通信质量。因此,提出基于Matlab的量子激光雷达稳频通信模拟系统。由于振荡器是雷达形成初始信号源的基础,通过分析振荡电路与相位噪声,获得相位噪声函数与通信频率存在的关系;为确保通信过程的稳定,将准确性与稳定性作为信号质量的评价指标,并采用锁频环稳频技术计算频率偏移程度,根据PID控制算法控制频率,量子激光雷达稳频通信;利用Matlab确定激光器、探测器等硬件组成结构,通过时序与数字阵列的设置完成模拟系统设计。仿真结果表明所提系统结构简便、性能稳定,能够真实模拟出稳频通信的信号质量。     

Research on phase shift characteristics of electromagnetic wave in plasma

The phase shift characteristics reflect the state change of electromagnetic wave in plasma sheath and can be used to reveal deeply the action mechanism between electromagnetic wave and plasma sheath. In this paper, the phase shift characteristics of electromagnetic wave propagation in plasma were investigated. Firstly, the impact factors of phase shift including electron density,collision frequency and incident frequency were discussed. Then, the plasma with different electron density distribution profiles were employed to investigate the influence on the phase shift characteristics. In a real case, the plasma sheath around the hypersonic vehicle will affect and even break down the communication. Based on the hypersonic vehicle model, we studied the electromagnetic wave phase shift under different flight altitude, speed, and attack angle. The results indicate that the phase shift is inversely proportional to the flight altitude and positively proportional to the flight speed and attack angle. Our work provides a theoretical guidance for the further research of phase shift characteristics and parameters inversion in plasma.